How To Remove A Dexter Door Knob

• Doors & Windows

How To: Remove and Replace a Doorknob

Hidden screws may brand this task seem mysterious. The right tools—and this guide—turn it into a simple matter.

Photo: dreamstime.com

We think of a doorknob equally ubiquitous and mundane, withal a closer inspection can sometimes prove puzzling, leaving you to wonder,Where are the screws that hold it in place? They're at that place, all right, if not outright visible then subconscious beneath the cosmetic collar known every bit the "rose." Removing and replacing the knob requires y'all to reach these screws without dissentious the door.

Before You Brainstorm

Before you can tackle the easy-enough-to-DIY chore, first sympathize the types of doorknobs on the market:

• About mod, standard-issue doorknobs are sold every bit a lockset, consummate with all necessary hardware—knob, rose, spindle, latch (too called a striker), and latch plate. Some of these knobs accept recessed hex-head screws, reachable with a uniform Allen wrench.
• Others have a thin hole through which y'all insert a firm wire (a straightened-out paper prune is perfect) to press on a spring-activated pin called a detent; this releases the knob from the spindle or shaft that connects both knobs through the latch assembly.
• On however other knobs, the detent access hole is actually a slot; use a thin, flat-head screwdriver to reach the detent with this type.

Determining which category your existing knob falls into will dictate the best way to remove and supervene upon it for a more updated mode.

Photo: dreamstime.com

Tools & Materials

• Allen wrench
• Paper prune
• Flat-head Screwdriver
• Phillips screwdriver
• Replacement lockset

Photo: dreamstime.com

How to Remove and Replace a Doorknob

STEP 1

Know your knob. Examine the lock side of the doorknob, looking for a tiny slot or pigsty; these are the detent access holes. Don't see it? Cheque instead for a recessed screw that you lot'll loosen with an Allen wrench of the appropriate size.

Step ii

Now, to how you go about releasing the knob depends on how it's attached.

• If you find a slot, insert the flat-head screwdriver and push the detent to release the knob.
• If you find a minor hole, use a straightened paperclip or other firm wire to spring it.
• If dealing with a recessed hex-caput spiral, turn information technology counterclockwise with an Allen wrench until the knob is free.

STEP 3

Remove the rose. In some cases, the rose must be removed separately in order to betrayal the screws that hold the backing plate to the door. If that's the case, locate the sparse slot in the seam between the plate and door, insert the tip of a apartment-head screwdriver, and pop off the rose.

STEP 4

And then, unscrew the works. Use a Phillips screwdriver to remove the screws that run from one bankroll plate to its contrary through the bore hole. These screws concur the entire knob and latch associates together. Remove the old knobs, bankroll plates, latch, and spindle.

STEP five

Replace the latch plate, the piece of metal attached to the door jamb through which the latch passes when the door is completely closed (as well called a strike plate). Even if it looks fine, you'll need to remove and supplant it, using a Phillips screwdriver, to ensure compatibility with the new knob hardware.

Need a hand?

Receive complimentary, no-delivery projection estimates from qualified pros near you.

+

STEP 6

Install the new latch, ensuring that the curved side of the striker faces the same fashion the original one did so the door latches properly.

STEP 7

Set the new knob in place, starting from the outside, or locking side, of the door. (The rose might exist office of the knob associates, or it might need to exist installed separately, before the knob itself.) Repeat on the inside knob. Position the spindle and mounting screws through the latch assembly from the outside and into the base of the reverse knob. Tighten all screws using a Phillips caput screwdriver. Slide the knob on the end of the spindle and plough it until the detent clicks into alignment with the access slot or hole. Tighten recessed screws with the Allen wrench if necessary.

Knock, knock! Who's there? Your make new doorknob, looking great and performance smoothly.

Demand a manus?

Receive free, no-commitment project estimates from qualified pros nearly you lot.

+

Source: https://www.bobvila.com/articles/how-to-remove-a-doorknob/

Share this post